How to Prevent and Manage Soil Salinity
There are various practices that you can apply, in order to prevent soil salinity or manage salinity problems once they already occur.
1. Select a crop that fits the conditions in your field
- Soil type – water infiltration capacity, how much air does the soil contain ,how much water will be needed to wash the soil in order to avoid salinity build up.
Does your soil have special drainage problems? For example, it is better avoid planting a salt sensitive crop in a soil which is not well drained.
- The microclimate conditions in the field – parameters such as wind direction and solar radiation may affect water consumption of the crop.
- The agricultural history of the field – did salts accumulate in the soil during a previous crop?
- Irrigation water quality – Check the quality of the available source water.
What kind of salts does it contain and what is the total level of salts in it?
- Type of irrigation system and its distribution – what type of irrigation system are you going to use?
Is it flood irrigation, sprinklers, pivot or drip irrigation? Each type of irrigation system has its own water distribution pattern, depending also on the soil properties.
Make sure the emitters are set in the appropriate spacing, to allow uniform irrigation depending on your soil type.
2. Know the leaching requirement for your crop
Irrigation water amounts must coincide the growing stage of your crop.
Apply the minimum needed to flush salts from soil. This means that you always have to give a little more water than the crop consumption, to allow leaching of salts below the root zone.
Heavier soils require larger water applications than lighter soils, in order to avoid salinity buildup.
The leaching requirement is expressed as:
% Yield (of maximum) = 100 – b (ECe – a)
A general equation to calculate the leaching requirement is
LR (%) =ECiw/(5ECth-ECiw)
Where ECiw is the EC of the irrigation water, and ECth is the threshold salinity measured in the saturated soil extract, above which yield begins do decline (both in ds/m).
The total amount of water to be applied is AW = ET/(1-LR)
Where AW is the amount of water to be applied and ET is the water consumption based on evapotranspiration.
3. Keep the right Intervals between irrigations
Irrigation regimen and intervals must be appropriate to the soil conditions and to growth stage of the crop.
Frequent and shallow (superficial) applications result in salt accumulation in the root zone, while larger applications, in longer intervals, will flush the salts below the root zone.
4. Use appropriate fertilizers types
The fertilizers type and their quantities should coincide with to the requirements of the crop and with nutrients which are already in the soil. There are fertilizers which contain salts which are not taken up by plants in large amounts, such as chlorides.
These salts tend to accumulate in the soil.
5. Have your soil tested periodically
Soil analysis gives you a better indication of the salt content in the soil, without which you’ll be only guessing.
Guessing often comes close enough, but in many cases growers realize there’s a salinity problem only after yields are decreased or crop quality is reduced.
A practical approach in order to prevent salinity buildup early enough is sampling the soil 5 times over a growing period of 8 months (a test every 6 weeks or so). It is recommended to do at least one water analysis as well.
The tests will indicate any change in soil content, allowing you to adjust the fertilization and irrigation regimen as needed.
This is the cheapest, most practical way to follow up on salinity status, keeping your crop quality and yield at optimal level.
6. And if after all that, you still face a salinity problem…
When you identify a salinity problem during the growing season, it is recommended to flush the field, even if it means risking some crop damage, rather than allowing further deterioration of the crop due to salinity.
Flushing applications should be carefully planned according to the crop conditions and growth stage.
In light soils, which drain easily, the impact of flushing on the crop is usually insignificant.
In heavy soils, water infiltration and drainage problems may be encountered, resulting in excess of water and lack of air to the roots. Flushing heavy soils is a prolonged process and its final result is difficult to anticipate in advance.
Therefore, extra care should be taken when growing on heavy soils, as to not reach salinity buildup at all, or at least identify the problem early enough, when salts levels are still relatively easy to flush.
If all else fails and flushing is the chosen course of action, in heavier soils, not more than the maximal water amount that can be absorbed by the soil should be applied, and the longest intervals possible should be maintained. In the meantime, fertilization should be based only on Nitrogen and only the minimum amount should be applied.
The water used for flushing should be the highest quality possible, because the purpose of the flushing process is to decrease the soil salinity to the levels of the irrigation water.
- Recommends the ideal fertilizer mixture/ blends
- Saves up to 50% on fertilizer costs
- Comprehensive data on hundreds of crop varieties
- Interprets test results for any extraction method